Last updated: 22 November 2026 — Scotland Leak Detection
A UFH manifold is the hub where your underfloor heating loops connect to the boiler, with a flow meter per loop showing how much water is circulating. Even flow across all loops with stable pressure is normal. One flow meter reading noticeably low, or pressure that keeps dropping and needing topped up, points to a leak in that specific loop.
In This Guide
What the manifold actually does
The UFH manifold is the control point where the water heating your floor gets split out into separate loops and brought back together again. Each loop is a length of pipe embedded in or under your floor, and every loop needs the right amount of water flowing through it to heat its area properly.
Think of it as the dashboard of the whole system. Everything that matters, flow, pressure, temperature, shows up here first, before it shows up as a cold patch on your kitchen floor. Learning to read it takes ten minutes and saves you calling someone out for a problem you could have spotted yourself.
Most manifolds sit in a cupboard, utility room, or plant room, out of the way and easy to ignore. That's exactly why problems often run for weeks before anyone notices, the manifold was quietly showing the warning the whole time.
Reading the flow meters
Each loop on the manifold has its own flow meter, usually a small vertical tube with a floating indicator that rises with flow rate. Manufacturers mark a recommended range for each loop based on its length and the room it serves.
- All floats sitting steady within range: normal operation. This is what you want to see across every loop.
- One float sitting lower than the others: that loop is getting less flow than it should. This can mean trapped air, a partially closed valve, or, less commonly, a leak reducing pressure in that specific loop.
- A float that won't settle, bouncing or fluctuating: usually air in the system rather than a leak, though persistent air after bleeding is worth investigating further.
- A float reading zero with the loop valve open: either a blockage or a serious flow problem in that loop, worth checking urgently.

Why the pipe under the floor matters more than the manifold itself
The manifold tells you something's wrong. It can't tell you exactly where along a 60 or 80 metre loop of pipe, buried in screed, the problem actually is. That's the harder part, and it's where thermal imaging and pressure testing earn their keep, since nobody wants to lift an entire floor to find one small leak.
Normal pressure and what's off
Underfloor heating usually runs off the same sealed system as your radiators, fed from a combi boiler or a pressurised system. Normal cold pressure for a typical combi boiler is around 1 to 1.5 bar, and that figure applies whether or not underfloor heating is part of the circuit.
A system that holds its pressure steady day to day is behaving normally. A system that needs regular topping up, especially if you're doing it more than once every few months, is losing water somewhere, and an underfloor loop is one of the most awkward places for that to be happening, precisely because it's hidden under a solid floor.
Our guide on underfloor heating losing pressure goes into more detail on what different pressure-loss patterns tend to mean.
Isolating loops to test
If one loop looks suspicious, isolating it is the standard first diagnostic step, and it's something a competent tradesperson (or a confident DIYer) can usually do safely.
Step 1: Note the current readings
Write down every loop's flow rate and the system pressure before you touch anything. You need a baseline to compare against.
Step 2: Close the suspect loop's valves
Most manifolds have isolation valves on both the flow and return side of each loop. Closing both takes that loop out of the circuit without affecting the others.
Step 3: Watch the system pressure
If pressure stabilises once the suspect loop is isolated, that loop is the likely source. If pressure keeps dropping regardless, the problem may sit elsewhere in the system.
Step 4: Confirm before assuming
Isolating a loop tells you which one is suspect. It doesn't tell you exactly where in that loop's run the leak is. That needs proper detection equipment rather than guesswork.
One loop behaving badly on your manifold?
Our underfloor heating leak detection service pinpoints the exact spot in a loop without lifting the whole floor.
When gauge behaviour means a leak
Not every odd reading means a leak, and it's worth ruling out the simpler explanations first.
Probably not a leak
- Flow improves after bleeding air from the system
- Reading returns to normal after reopening a valve that was accidentally closed
- Pressure is stable, just slightly outside the ideal range
Points towards a leak
- Pressure drops steadily over days or weeks, repeatedly needing topped up
- One loop's flow stays low even after bleeding and valve checks
- A warm or damp patch on the floor above the suspect loop
We see this pattern often: a homeowner has been topping up pressure every month for a year, assuming that's just how the boiler works, when actually one loop has been slowly weeping the whole time. Our guide on signs your underfloor heating is leaking covers the other warning signs worth watching for alongside the manifold itself.
What we do differently
Reading the manifold gets you to "which loop", which is a genuinely useful starting point. Getting from there to "which metre of pipe" is where specialist equipment matters, because opening up an entire screed floor to search by trial and error is expensive and disruptive.
We use thermal imaging to spot the temperature signature of a leaking loop through the floor surface, and tracer gas testing, introducing a safe mix of 5% hydrogen and 95% nitrogen into the isolated loop, to pinpoint the exact leak location from where the gas escapes. Both are non-invasive, so you're not committing to opening the floor until you know precisely where to look.
This matters even more with underfloor heating than standard plumbing, since repairs usually mean cutting into screed or flooring that's expensive to replace. Getting the location right the first time saves real money.
Honestly, most manifold-related call-outs we attend end with good news. The system is usually fine, and it just needed air bled out or a valve reset. But when the readings genuinely don't add up after the basic checks, finding the exact spot before anyone lifts a tile is worth the extra step.
Frequently Asked Questions
It means that specific loop is getting less water flow than it should. Common causes include trapped air or a partially closed valve, but if it persists after bleeding and checking valves, a leak in that loop becomes the likely explanation.
Most systems fed from a combi boiler run at around 1 to 1.5 bar when cold. Consistent pressure day to day is normal. Regular, repeated drops that need topping up point to water escaping somewhere in the system.
Most manifolds have accessible flow and return valves per loop, and closing them is straightforward if you're comfortable with basic heating system work. Note your readings before and after, since that comparison is what tells you anything useful.
Once a loop is isolated as the likely source, thermal imaging and tracer gas testing pinpoint the exact spot along its run, without lifting the floor to search by guesswork. This is far cheaper than opening up an entire room.
Frequent topping up means water is leaving the system somewhere. It could be a small leak in a loop, a fitting at the manifold itself, or elsewhere in the heating circuit. It's worth investigating rather than just continuing to top up indefinitely.
Not usually. A fluctuating float is more often trapped air in the system, which bleeding will usually resolve. If it keeps happening after bleeding and checking the valves, that's when it's worth investigating further.
Related Reading
- 5 Signs Your Underfloor Heating Is Leaking
- Underfloor Heating Losing Pressure? Here's What It Means
- How to Prevent Frozen Pipes in Scotland This Winter
Or explore our underfloor heating leak detection service.
📍 Professional Leak Detection Across Scotland
Don’t let a small problem become a big one
If your manifold readings look off, we’ll pinpoint the exact loop and location with non-invasive methods before anyone touches the floor.
