Last updated: 17 October 2026 — Scotland Leak Detection
Brown water from taps is usually iron sediment stirred up in the mains, often after nearby repair work or a burst. Run a cold tap for a few minutes; if it clears, it was mains disturbance. If it stays discoloured, keeps returning, or only affects hot water, ageing internal pipework or a leak is more likely and worth investigating.
In This Guide
Why water turns brown
Brown or discoloured tap water almost always comes down to iron and manganese sediment that has built up naturally on the inside of water mains over years. Under normal conditions it sits undisturbed. Anything that changes the flow or pressure in the network, a burst, a repair, or even fire crews drawing heavily from a hydrant nearby, can stir that sediment loose and send it through to nearby properties.
It looks alarming, especially the first time, but it’s a cosmetic problem in the vast majority of cases rather than a sign of contamination. That said, it’s still worth running the tap and checking whether it clears, rather than assuming and ignoring it.
The colour itself can be a useful clue. A yellowish or light brown tinge usually points to iron sediment, the most common cause. A darker, almost black tint is less common and can indicate manganese deposits, which behave similarly but build up differently in certain parts of the network. Either colour responds the same way to the run-clear test, so you don’t need to diagnose the exact mineral, just whether it clears with steady running.
Older Scottish towns with cast iron water mains still in service, some dating back well over a century, are more prone to this kind of sediment build-up than areas with newer plastic mains. That’s simply down to the age and material of the network in a given street rather than anything about water quality itself.
The run-clear test
1. Run a cold tap only
Use a tap unconnected to any filter or softener, ideally the kitchen cold tap, and run it steadily rather than in short bursts.
2. Give it a few minutes
Mains-related discolouration usually clears within a few minutes of steady running. If it hasn’t cleared noticeably after five to ten minutes, stop and reassess rather than running it indefinitely.
3. Check other cold taps in the house
If every cold tap shows the same brown tinge, that points to the mains supply or the pipe between the mains and the house. If only one tap is affected, the cause is more likely local to that fitting or its immediate pipework.
4. Test hot water separately
If only hot water is discoloured while cold runs clear, the cause is inside the property, most likely sediment or corrosion in the hot water cylinder rather than anything to do with the mains.

Don’t waste more water than you need to
Running a tap to test for clearing is sensible, but there’s no need to leave it running for an hour "just in case". A few minutes tells you what you need to know. If it hasn’t cleared by then, the better move is reporting it or getting the internal pipework checked rather than continuing to run water down the drain.
Mains disturbance vs your own pipes
Mains disturbance affects a wider area, often several properties on the same street, and tends to arrive suddenly rather than building up gradually. It’s usually linked to a specific event: works nearby, a burst reported in the area, or unusually high demand on the network.
Discolouration from your own pipework tends to be more localised and often builds gradually rather than appearing overnight. Older galvanised steel supply pipes, still found in some older Scottish properties, corrode from the inside over decades, and rust particles can shed into the water especially after the pipe has sat still overnight or over a weekend away.
Signs it’s the mains
- Neighbours report the same issue
- Started suddenly, often same day as nearby works
- Clears within minutes of running the tap
Signs it’s your own pipework
- Only affects your property
- Worse first thing in the morning
- Doesn’t fully clear even after running the tap
When discolouration follows a repair
If brown water appears shortly after Scottish Water or a contractor has carried out repair work nearby, that’s a strong signal the disturbance is mains-related. Repair work changes flow patterns in the pipe network, sometimes reversing flow direction briefly, and that’s exactly the kind of disruption that dislodges built-up sediment.
This kind of discolouration is usually temporary and clears within a day or two as the network settles back into its normal flow pattern. If it’s still happening a week after nearby works finished, that’s worth flagging directly rather than assuming it will keep improving on its own.
Water still discoloured after running the tap?
If brown water keeps coming back and isn’t linked to any nearby mains work, we can check whether a leak in your own supply pipe is disturbing sediment or corroding pipework from within.
Reporting it to Scottish Water
Report ongoing or unexplained discoloured water to Scottish Water’s 24/7 leak and supply line on 0800 077 8778, per mygov.scot. They can tell you whether known works or a burst in your area explains it, and can arrange flushing of the local main if sediment build-up is the cause.
If you report an issue and aren’t satisfied with the response, the Scottish Public Services Ombudsman handles unresolved complaints about Scottish Water’s service. Most discolouration cases resolve well before that stage, but it’s there if needed.
When it points to a leak
Persistent discolouration that doesn’t trace back to nearby mains works can sometimes go hand in hand with a leak on the supply pipe between the mains and your property. A leak changes local pressure and can pull sediment through a weak or corroding section of pipe, particularly in older lead or galvanised steel supply pipes still found in parts of Scotland’s older housing stock.
If discolouration comes with other signs, a drop in water pressure, a damp patch in the garden, or a water meter that keeps ticking over when nothing’s running, it’s worth getting the supply pipe checked properly. Water leak detection and water mains leak detection use acoustic and tracer gas methods to trace a leak along its full run without digging up the garden speculatively.
Under the Scotland-specific responsibility split, Scottish Water looks after the mains up to your property boundary, and you’re responsible for the pipe from the boundary into the house, according to Citizens Advice Scotland. That split matters for who arranges and pays for any repair once a leak on the supply pipe is confirmed.
Frequently Asked Questions
Avoid drinking it until it’s run clear. In most cases the discolouration is iron sediment rather than contamination, but running the tap until clear and reporting persistent issues is the sensible precaution. If it doesn’t clear within a few minutes, call Scottish Water on 0800 077 8778.
This usually points to sediment or corrosion inside your hot water cylinder rather than the mains supply. Cold water running clear from the same tap confirms the mains and your cold supply pipe aren’t the source. A plumber can inspect or flush the cylinder to confirm it.
Most clears within a few minutes of running a cold tap, and any residual discolouration in the area typically settles within a day or two once the network stabilises after the disturbance. If it persists beyond that, report it rather than waiting for it to fix itself.
Call Scottish Water’s 24/7 line on 0800 077 8778. They can confirm whether known works or a burst explains the discolouration and arrange flushing of the local main if needed. If a complaint isn’t resolved, the Scottish Public Services Ombudsman is the next step.
Yes. A leak can change pressure in the supply pipe and pull sediment through corroding or ageing pipework, especially in older lead or galvanised steel supply lines. Persistent discolouration alongside other signs like low pressure is worth investigating properly with a non-invasive survey.
It’s sensible to hold off until the water runs clear, since sediment can stain laundry or leave marks on dishes. Once a cold tap runs clear for a few minutes, it’s generally fine to resume normal use. Run the machine’s cold feed briefly before starting a full load.
Related Reading
- Low Water Pressure in Your House? Causes and Fixes
- Who Is Responsible for Water Pipes in Scotland?
- How to Use a Water Meter to Check for Leaks
Or explore our water leak detection service.
📍 Professional Leak Detection Across Scotland
Don’t let a small problem become a big one
If discoloured water keeps returning and mains work doesn’t explain it, our non-invasive surveys can trace whether a leak in your supply pipe is the cause.
